Drivers Update: ECS GeForce7050M-M NVIDIA RAID
ECS GeForce7050M-M NVIDIA RAID Driver
Build a ECS ECS GeForceM-M Mobo PC with our PC builder. The ECS GeForceM-M is compatible with AMD processors with the Socket AM2 socket. It has 16 GB DDR2 RAID Support, yes. help icon The ECS GeForceM-M does not support multiple graphics cards via Nvidia SLI or AMD Crossfire. Make sure your M/B PCB version number first, and then read the updated description & special note carefully to check if the new BIOS version patch pertain to. View and Download ECS GeForce M-M manual online. Chapter 5 Setting Up NVIDIA RAID Configuration There are two ways to setup NVIDIA RAID.
|Supported systems:||Windows 10, Windows 8.1, Windows 7|
|Price:||Free* [*Free Registration Required]|
ECS GeForce7050M-M NVIDIA RAID Driver
Remove a blanking plate from the system case corresponding to the slot you are going to use.
Install the edge connector of the add-on card into the expansion slot. Ensure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card to the system case with a screw.
ECS GeForce7050M-M - 2.0 - motherboard - micro ATX - Socket AM2+ - GeForce 7050PV
Front Panel Audio header Optional This header allows the user to install auxiliary front-oriented microphone and line- out ports for easier access. Additionally, some computer cases have USB ports at the front of the case.
If you ECS GeForce7050M-M NVIDIA RAID this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard. Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive.
Connecting Case Components Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: Connect the standard power supply connector to PWR1.
- ECS > GeForceM-M (V)
- ECS > GeForceM-M (VA)
Connect the auxiliary case power supply connector to PWR2. ECS GeForce7050M-M NVIDIA RAID to the table below for infor- mation: The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry.
The layout of board's components is overall reasonable. The latches on memory slots are not overlapped by a long graphics card.
Both PCI slots are also accessible after installing a graphics card with a cooler of any size. The jumpers are easily reachable after the board is equipped with an expanded set of peripherals. Detailed designation of contacts is shown in charts nearby on the board's surface.
Only the SATA ports give a formal reason for criticism, because they can be partially blocked by the graphics card cooling system. A simple heatsink provides chipset cooling with a wide safety margin. Even under load it heats up very little.
ECS GeForce 7050M-M Manual
All components allowed for by design, except an LPT port and three audio-out sockets for an 8-channel audio codec, are present on the board. This is the only model based on the given chipset in the ECS product line, while the ECS GeForce7050M-M NVIDIA RAID missing elements may, probably, be included in the batches produced for OEM orders. The three-channel CPU supply impulse voltage regulator uses 2 field transistors per channel, 6 microfarad Sanyo capacitors and 3 microfarad OST capacitors.
The board's form-factor is x mm a cut-down microATX.
ECS GEFORCE M-M MANUAL Pdf Download.
It is mounted to the chassis using 6 screws while the right edge up to the storage sockets remains unsecured. Voltage ECS GeForce7050M-M NVIDIA RAID CPU core and memory; Rotation rate of the CPU fan; Temperature of CPU by built-in CPU sensor and of the motherboard by on-board sensor ; Smart Fan, automatic control for a fan with 4-pin connector and an ability to set two temperature thresholds corresponding to activation of gradual rotation rate adjustment and the fan's maximum rotation rate mode.
Within the temperature range ECS GeForce7050M-M NVIDIA RAID rate grows according to the "Fan Slope" value, which sets the percentage increase in rotation rate for each degree of increase in temperature. Unfortunately, the packages from ECS are becoming incresingly scarce.